1LT1056X2• 9/24/98BARNSTEAD|THERMOLYNE CORPORATIONEASYpure™ UV/UFOPERATION MANUALAND PARTS LISTSeries 1056
10you. Viewed this way, the product connector isthe one on the left. The reject connector is theone on the right. (See Figure 5) Remove the nut,stainl
117. Locate the UV chamber. Carefully remove theblack plastic cover from the UV chamber bypulling the cover straight up. Do not pull onthe cable.8. Re
12Wall Mounting (Optional)Install the optional wall bracket on the wall in a location thatis accessible to water, electricity and an atmosphericallyve
13Reject Water ConnectionWhen the EASYpure UV/UF flushes its membrane, thewater used is sent to drain through this connection. Toinstall:1. Locate the
14Main Power SwitchThe main power switch on the EASYpure UV/UF is located onthe back right of the unit (as you face the front of the unit),directly ab
15Pressing the Flush switch twice will initiate a five minuteflush of the ultrafilter. During this five minute flush, wateris sent to drain through th
16Run ModeSince not all qualities of permissible feedwater will reachmaximum resistivity after one pass through the unit’scartridges (especially as th
17Initial SanitizationYour EASYpure UV/UF has been shipped with a sanitiza-tion cartridge (Catalog Number D50245) and two emptycartridges to allow you
188. Open the draw-off valve to depressurize thesystem. Leave valve open until solutioncompletely stops flowing, draining as muchof the system as poss
1910. Press the “Flush” button twice to begin anextended flush. When water begins exiting thesystem, close the draw-off valve.11. When the extended fl
2Table of ContentsSafety Information ...
201. Press the START/STOP button to start. TheEASYpure UV/UF’s pump will begin to run andthe Purity meter will display the resistivity of thewater in
21Installing Float or PressureSwitchAccessories D0606 (float switch) and D2706 (pressureswitch) are designed to protect the EASYpure UV/UFpump by aler
22System Sanitization and CartridgeReplacementThe frequency with which you will need to clean your unit andreplace cartridges is dependent on your fee
238. Repeat steps 2 - 6 with the two empty car-tridges supplied with your EASYpure UV/UF,placing them in the center and left-handpositions.9. Close th
24Ultrafilter ReplacementThe length of your ultrafilter’s life will depend to someextent on conditions and use in your lab. When you areunable to comp
25necessitating the EASYpure UV/UF be placed in a recircu-lating mode for up to one hour to achieve organic content of2 ppb TOC.To replace the ultravi
2612. Reattach the power cord and the pump protectoror the pump interlock and reconnect the unit tothe power supply.13. Operate normally.Fuse Replacem
27UV Solid State Ballast FuseReplacement1. Turn off the EASYpure UV/UF and disconnectit from the power supply. Remove the powercord and the pump prote
282. Depressurize the system by opening thedraw-off valve, allowing water to drain untilno more flows from the valve.3. Open the cartridge access door
2916. Reinstall the screw holding the cell-cable retain-ing clip. Reinstall membrane switch lead. Re-place the front cover. Replace the Luer fitting w
3Safety InformationYour Barnstead EASYpure™ UV/UF has been designedwith function, reliability, and safety in mind. It is yourresponsibility to install
30TroubleshootingProblem Possible Causes SolutionsEASYpure UV/UF completely No electrical power to Ensure that the EASYpureinactive. (Pump not operati
31TROUBLESHOOTINGProblem Possible Causes SolutionsRecirculated water will not rinse Exhausted cartridge Replace the cartridge asup to desired purity l
32Problem Possible Causes SolutionsIf a Barnstead Still is theShort cartridge life (cont.) feedwater source, ensure that themembrane is functioning pr
33ConsumablesConsumable parts are those required to support the day-to-day operation of this equipment.Barnstead|Thermolyne establishes two types of c
34General MaintenanceGeneral maintenance parts are defined as laboratory level repair parts which do not require great expertise orspecial tools for i
35100 Volt Wiring SchematicWiring DiagramsNANONANOGNDL2L1PUMPPRODFEEDPUMPFEEDPRODBLACK100 VAC, 50/60 Hz3.0 ALINEGROUND1FILTERLINE1PUMP INTERLOCKWITH J
36120 Volt Wiring SchematicWIRING DIAGRAMSGND120 VAC, 50/60 HzGROUNDLINE1LINEFILTER1PUMP INTERLOCKWITH JUMPER PLUGFOR USE WITHOPTIONAL PRESSUREOR FLOA
37230 - 240 Volt Wiring SchematicWIRING DIAGRAMSGND240 VAC, 50/60 HzGROUNDLINELINEFILTER1PUMP INTERLOCKWITH JUMPER PLUGFOR USE WITHOPTIONAL PRESSUREOR
38Exploded Views
39EXPLODED VIEWS
42. This device is to be used with water feeds only.Sanitizing/cleaning agents must be used incompliance with instructions in this manual.Failure to c
40Ordering ProceduresPlease refer to the Specification Plate for the complete model number, serial number, and series number whenrequesting service, r
41Barnstead|Thermolyne Corporation warrants that if a product manufactured by Barnstead|Thermolyne andsold by it within the continental United States
42
449001ISOREGISTEREDBarnstead|Thermolyne2555 Kerper Blvd.P.O. Box 797Dubuque, IA 52004-2241Phone: 319-556-2241 800-553-0039Fax: 319-589-0516E-Mail Ad
5The Barnstead EASYpure UV/UF is a line-fed waterpurification system designed to provide pyrogen-free, lowTOC reagent grade water that exceeds ASTM, T
6Dimensions and Clearance RequirementsEASYpure UV/UF dimensions: 12 " W X 19" D X 17 1/8" H (30.5 cm X 48.3 cm X 43.5 cm).Clearances:Si
7Environmental ConditionsOperating: 4°C - 49°C; 20% - 80% relative humidity,non-condensing. Installation Category II(over-voltage) in accordance with
8Unpacking1. Remove the unit from its shipping container.Ensure that the ultrafilter, UV lamp, feed and rejecttubing, final filter, sanitization cartr
93. Place the grab ring and back-up ring in the hexnut in the order and orientation shown in Figure3. Thread the nut onto the adapter. DO NOT usethe o
Kommentare zu diesen Handbüchern